Marketplace

Production of products according to drawings - pallets for shipment

Provision of transportation services for the transportation of employees to the place of work and back along the route according to the Requirements Specification.

Service and repair of air conditioners on the territory of the enterprise.

Repair of coating (gumming) of rollers Restoration of shafts with polyurethane coating

Repair of coating (gumming) of rollers. Restoration of shafts with polyurethane coating.

Production of the axle of the wheelset on the freight transfer cart according to the Customer's drawing - 1 pc. Material: 40GM steel. Manufacturing of the axle of the wheelset on the cargo transfer cart.

Selection of a contractor to carry out repair and construction work. Repair of the steps of the entrance group. Laying paving slabs.

1. The leading drum (with cold gumming): • Drawing: TM 2123.00.000 • Quantity: 2 pcs. • Material for manufacture: St3, 09G2S, St20

1. Drive drum: • Drawing: TM 1944.00.000 • Quantity: 2 pcs. • Material for manufacturing: St3, 09G2S, St20

1. Drum (right): • Drawing: TM 2019.00.000 • Quantity: 1 pc. • Material for manufacture: 09G2S, St20 • The cylinder is made of pipe 351*22 steel 09G2S 2. Drum (left): • Drawing: TM 2020.00.000 • Quantity: 1 pc. • Material for manufacture: 09G2S, St20 • The cylinder is made of pipe 351*22 steel 09G2S

1. The shaft of the presser: • Drawing: 0, S220017 • Quantity: 4 pcs. • Material for manufacturing Steel 38NiCrMo4 or 40KHN2MA 2. The shaft of the presser: • Drawing: 0, S220018 • Quantity: 4 pcs. • Material for manufacturing Steel 38NiCrMo4 or 40KHN2MA 3. The shaft of the presser: • Drawing: 0, S220019 • Quantity: 4 pcs. • Material for manufacturing Steel 38NiCrMo4 or 40KHN2MA 4. The shaft of the presser: • Drawing: 0, S220020 • Quantity: 4 pcs. • Material for manufacturing Steel 38NiCrMo4 or 40KHN2MA

Impeller DO1111.000.01.010SB - 2 pcs Drying Fan

Provision of energy audit services for an industrial enterprise. The following are subject to energy audit: 3.1. Facilities of the enterprise: production building with technological equipment, production premises of tenants, 4-storey ABC building; 3.2. Equipment of the main technological process: - Redman paint line (gas is used for the technology of the paint line); - "Hana" mill; - "Comec" mill; - Samesor mill; - "SS10" mill; - mill "C10"; - Andalusia camp; - edge bending press "Horns"; - the line of longitudinal-transverse metal cutting "LSK"; - compressor room (5 pieces of equipment); - overhead cranes (4 pieces of equipment); - built-in boiler room for heating water for heating and hot water (12 months) boiler "Micro- M 200" - 3 pcs. with a capacity of 200 kW; - TG "Kroll 360 S-250" power 300 kW. with burner Giersch MG10/1 – 4 pcs.; - TG "Carlieuklima B350" power 400 kW. with burner Cibunigas NG550 – 3 pcs.; - TG "Carlieuklima B160" power 186 kW. with burner Cibunigas NG200 – 2 pcs.; - TG "Carlieuklima V110" power 127 kW. with burner Cibunigas NG140 – 1 pc. Provision of energy audit services for an industrial enterprise

1. Replaceable superstructure (MVP-1) • Material for manufacturing Steel 3, Sheet 10; • Quantity – 40 pcs. (a=40mm, b=280mm) • Drawing - TM 1676.00.000 2. Removable extension (MVP-2) • Material for manufacturing Steel 3, Sheet 10; • Quantity – 40 pcs. (a=35mm, B=363mm) • Drawing - TM 1676.00.000

1. Sealing brush: • Material for manufacturing Steel 3; • Quantity – 60 pcs. • Drawing – TM 1948.00.000

Manufacturing of the side seal of the Design and Survey Work line (roof 80 mm and 120 mm) from heat-resistant antistatic polyethylene PE-500 (with an operating temperature of 80'S) of lining elements in the amount of - 100 pcs. size 80mm; - 100 pcs size 120mm It is allowed to replace the material with PE-1000 (antistatic). The service life after manufacture is at least 2 years. Manufacturing of the lateral seal of the Design and Survey Work line (roof 80 mm and 120 mm) from heat-resistant antistatic polyethylene PE-500.

Manufacture of the valve body adhesive on the equipment of the Robor production line. Material - D16T. Quantity - 10 pcs. Not allowed: 1. Burrs 2. Blunt sharp edges with a radius or chamfer of 0.3... 0.5 mm. You can get acquainted with the design documentation from a technical specialist on request - Posashkov Alexey Borisovich mail: Aposashkov@elshield.com Manufacture of the valve body adhesive on the equipment of the Robor production line

Price monitoring requests for the calculation of Initial Maximum Prices No. 474162 "supply of construction and finishing materials"

Rolled metal MG-9523, 10025, 10135 Important: fill out the Technical and Commercial Proposal in the form attached to the bid documentation and attach it in Excel format, as well as attach the Technical and Commercial Proposal printed with signature and seal.

Metal products The Bidder of the Call for Bidding must attach a commercial offer according to the Customer's form (Appendix No. 1) with the signature of the responsible person, as well as in an editable format, it is necessary to fill in all the lines highlighted in yellow.